1 3

14.85 mm I.D. Dry Pellet Pressing Die - Die-15D-B

14.85 mm I.D. Dry Pellet Pressing Die - Die-15D-B

16 in stock

$319.95 USD
$319.95 USD
Sale Email for Lead Time

SKU:  DIE15DB

View full details

Die-15D-B is a 14.85mm I.D. pressing die set for making 14-15 mm diameter sample pellets. The pressing die is made of high-stretched and highly polished carbon steel to achieve high hardness to meet the essential requirements of making ceramic or metal samples. 
( Modified structure from April 10 for quicker release )


SPECIFICATIONS:

Model Number Die-15D-B
Maximum Load 16 metric Ton (at room temperature)
910 MPa
Material HRC 60 - 62 hardened steel 
Ra 0.08μm highly polished steel
All pressing dies are made of high-stretched carbon steel to achieve high hardness to meet the essential requirements of making ceramic or metal samples. Otherwise, the pressing surface could probably get scratched.
Material Requirement
  • 32-75 Microns
  • Do not use this die set for pressing powder with a particle size of 30 microns or smaller; Small particles may slip into the gap of the die parts and damage the sleeve during the compression.
  • Ball mill or ground the powder to the size of 32~75 microns powder before pressing. Please consider using the 3'' Dia. Sieve Set No.200&450 Mesh to separate the 32~75 microns particles from the powder clumps.
  • For pressing sticky metal powders such as Al, Mg, and Zn, it is necessary to use dry or alcohol-based tool lubricant to lubricate the die and sleeve set to reduce friction during the compression. 
Package Content
  • One pressing die sleeve
  • One top-pressing die
  • One bottom-pressing die
  • One support plate
  • One die kit container
Safety Precaution     
  • To avoid the risk of accidents and damage to the Pressing Die, please read these instructions carefully before installation and before using it for the first time.
  • Read the manual, especially the die installation schematic, before the operation.
  • Do not press flammable, explosive materials.
  • The operator must wear a protective goggles.
  • You must have a hydraulic pellet press equipped with the Protection Cover, please click the pictures left to order.
  • To avoid damaging the die core and sleeve, we strongly recommend pressing powder with a professional laboratory hydraulic press to ensure the evenest pressing interface and uniform pressure force.
Pressing Die Installation Schematic / Instruction
  1. Mixing and grinding chemical powder by agate mortar or Ball Mill
  2. Calcine mixed the powder in a high temp furnace under a suitable temperature
  3. Crushing and Grinding calcined powder again by mortar or ball mill
  4. Put calcined powder into the die
  5. Pressing sample by a pressing machine under suitable pressure
  6. ( You may use CIP to press again to increase density by about 5 - 10%.)
  7. Take out the pellet sample from die
  8. Sintering the pellet under a suitable temperature
Application Notes
  • Use ethanol to clean the pressing die before and after use every time
  • Use anti-rust oil after the operation and store the kit inside the original box in a dry place to avoid rusting.
  • You may consider using BNMR for easy mold release. Please click the picture below to order.
  •    

 

Related Products

Pressing Die 1/8" - 3" 
Laboratory Mill & Mixer

Powder grinding & Mixing
Gravity Convection Ovens, Max. 300C

Drying Ovens

Calcining & Sintering

Hydraulic Press
CIP - Cold Isostatic Press

 

×

Dimension:

A: Support Plate Thickness: 10mm
B. Sleeve O.D.: 45mm
C. Die Sleeve Height: 46mm
D. Sleeve I.D. : 14.85mm + 0.03-0.05mm 
E. Top Pressing Rod Body Length: 28mm

F. Top Pressing Rod Head Thickness: 5mm
G. Pressing Rod Diameter: 14.85mm ± 0.1mm 
H. Bottom Pressing Rod Body Length: 23mm
I. Bottom Pressing Rod Head Thickness: 7.8mm

Weight:

  • 1.3 lbs.

This product is a consumable product and all consumable products are NOT covered by MTI's warranty. Make sure to inspect for defect(s) thoroughly before use. 

Manufacturer Part Number: