• 9 KN (+/- 5N) Lamination Hot Press (200x150 mm) up to 150C with Precision Pressure Controller - YLJ-HP80
1 2

9 KN (+/- 5N) Lamination Hot Press (200x150 mm) up to 150C with Precision Pressure Controller - YLJ-HP80

9 KN (+/- 5N) Lamination Hot Press (200x150 mm) up to 150C with Precision Pressure Controller - YLJ-HP80

Low stock: 3 left

Price: RFQ

SKU: YLJHP80

Choose your Variant:



View full details

YLJ-HP80 is a Pneumatic Press with a precision constant pressure controller within +/- 0.5 Kg up to 9KN and 150°C. It is designed for testing the effect of pressure on solid-state battery performance, and also can be used as the SEI formation or electrode lamination under hot pressing. This device is Ar gas compatible and can be used in the glovebox.

SPECIFICATIONS:
Pneumatic Press
  • Max. Load: 9KN ( 900 Kg)
  • Pneumatic cylinder travel distance 200 mm Max.
  • Working area: 200 mm W x 150 mm D
  • Max. working height: 0 - 110 mm
  • Driven by any standard air compressor or inert gas tank, which is not included. 0.4~0.8Mpa of air pressure supply is needed. Please click the picture below to order.
  • Attention: If a gas cylinder is used instead of an air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn about the installation of a gas regulator.

Note: If used in the glove, an inert gas cylinder must be used for the gas source.

 pic1  pic2
Heating Plates
  • Two heating plates with two independent single point temperature controllers 
  • Single point PID temperature control with +/- 1ºC accuracy
  • Heated plate area: 200 mm W x 150 mm D
  • Max. working temperature: 150°C (continuous)
  • Heating Rate: 15°C/ minute Max.
  • Power: 220V (50/60 Hz), 1200 W
Pressure Controller
  • Pneumatic cylinder bore size 125mm diameter.
  • Digital pressure controller with PID tuning, which can keep the constant pressure at setting value.
  • 30 segments programmable. (max working time: 9999 minutes for each segment)
  • Pressure Accuracy: +/- 0.5 kg /cm2
  • Optional: You may order the load cell below to calibrate the applied pressure force from time to time
Feed-Through (Optional)
  • If the press is used in a glove box, two separate feed-throughs are required
    • One feed-through for gas tubes.($295.00/set)
    • One feed-through for power and communication cords.($500.00/set)
  • The feed-throughs are not included in the standard package, please contact us for more information.
Compliance
  • CE approval
  • NRTL or CSA certification is available upon request at an extra cost of $3500.00
  • Calibration: Please use NIST certified load sensor to calibrate the pressure by yourselves. ( Please click the picture below to order:
Application Notes
  • It can be used as a jig for compressing pressure adjustable split test cell, please click the picture below for details:
 compress-able coin cell Compress-able pouch cell
Operation Manual & Video

 

×

Dimension:

  • Press: 245 L x 480 W x 620 H, mm 
  • Pressure Programmer: 250 L x 230 W x 120 H, mm

Net Weight:

  • 80 lbs 

Shipping Weight and Dimension:

  • 135 lbs, 40"L x 25"W x 35"H

MTI offers a One-Year limited warranty with lifetime support(may cause a fee) for this product.

The MTI One Year Limited Warranty does NOT cover

  • Consumable parts such as O-rings, crucibles, screws, washers, etc.
  • Any damage and rust resulting from improper storage or maintenance.
  • Any damages caused by the use of corrosive and acidic gases.
  • Any damage resulting from failing to adhere to the individual product's specific operation requirements, such as water cooling, venting, etc.
Manufacturer Part Number: