1 6

Heating Sealer for Continuous Top/Side Sealing of Pouch Cells (Max. 190×190×12 mm) - MSK-140-AM

Heating Sealer for Continuous Top/Side Sealing of Pouch Cells (Max. 190×190×12 mm) - MSK-140-AM

Out of stock

Price: RFQ

SKU: MSK-140-AM

Choose your Variant:



View full details
MSK-140-AM is a multifunctional heater sealer for continuous top/side sealing of pouch cell (Max. 190×190×12 mm), whichi is realized by the special design of dual sets of heating blades and cell fixture. The absolute length of sealing blades is 210 mm and its effective sealing length is 190 mm. The temperature unifomity of sealing blade is ± 2.5 °C. The sealing width of soft top sealing blade and hard side sealing is 3.5 mm 6 mm, respectively.

SPECIFICATIONS:
Power Supply AC220V±10%, Single Phase, 50/60Hz, 2 kW
Pouch Cell Size

Max. L190×W190 ×T12 mm; Min: L62×W46 ×T2 mm (Smaller sizes requires customized fixture)

 
Sealing Length Sealing blade length is 210 mm, the maximum effective sealing length is 190 mm. 
Sealing Width Top Sealing: standard soft sealing width is 3.5 mm. customized sealing width of 2-10 mm is available upon request
Side Sealing: 
Sealing Thickness 0-0.5 mm for pouch cell case
Sealing Accuracy Thickness' uniformity is better than 0.03 mm
Sealing Pressure Max. 160 kgf (corresponds to a gas pressure of 0.6 MPa)
Sealing Temperature Max. 250°C (hard side sealing blade with Teflon tape at 220°C; soft top sealing blade with Teflon tape at 250°C).
Normally we recommend 180°C for sealing blades. 
Sealing Time 0-99s adjustable, normally 4-8s was recommended. 
Production Efficiency 100-200 pcs/h (depends on the proficiency of operators)

Sealing Pressure

pic 1pic 2
  • 0 - 0.7 Mpa (0 - 99 psi) adjustable
  • Air compressor tube size is 8.
  • (2-gallon air compressor is required, but not included. pls order at your store or the related product below )
  • Note: If a gas cylinder is used instead of an air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn the installation of a gas regulator.
Air Consumption 0.09 L / Sealing
Certification CE Certified
NRTL or CSA certification is available upon request at the extra cost.
Application Notes
  • Suggested Sealing Parameter: 
    • Upper Heating Blade Temperature: 200°C
    • Lower Heating Blade Temperature: 180°C
    • Pressure: 40 psi
    • Duration: 3 seconds
  • Please wait until both dies reached the Setting temperature, then begin to operate.
Sealing Die Tape
Adhesive Heat Sealing Tape (for MSK-115/140 series) 300X400mm/sheet, 5 MIL, 260C max. - EQ-MSK140-HST 		Please click here to order our sealing die tape for repair/spare use.

 

×

Dimension：

  • 650 mm (L) x 550 mm (W) x 650 mm(H)

Net Weight:

  • ~60 kg

MTI offers a One-Year limited warranty with lifetime support(may cause a fee) for this product.

The MTI One Year Limited Warranty does NOT cover

  • Consumable parts such as O-rings, crucibles, screws, washers, etc.
  • Any damage and rust resulting from improper storage or maintenance.
  • Any damages caused by the use of corrosive and acidic gases.
  • Any damage resulting from failing to adhere to the individual product's specific operation requirements, such as water cooling, venting, etc.
Manufacturer Part Number: