1 3

Economic Flat Slot Die Coater (optional 50 or 100mm Width) w/ Heating Vacuum Bed - MSK-AFA-III-FSC

Economic Flat Slot Die Coater (optional 50 or 100mm Width) w/ Heating Vacuum Bed - MSK-AFA-III-FSC

Low stock: 4 left

Price: RFQ

SKU: MSKAFAIII-FSC125V110

Choose your Variant:



View full details

MSK-AFA-III-FSC is an economic flat slot die with a 100mm coating head. It is an excellent tool to research film coating for perovskite solar cells, fuel cell proton exchange membrane, and the battery electrode.

SPECIFICATIONS

Working Power
  • 110VAC or 208 - 240V AC 50/60Hz selectable from product option
  • 1500W 
Slot Died head
  • Slot die head fixtures with coating widths of 50mm and 100 mm are available in the product options bar
   
 

Syringe Pump
  • Digital Controlled Infusion Syringe Pump and connection pipe are included
  • Displays total volume dispensed in mL or µL units
  • The maximum pumping rate of 25 mL/hr with a 60 mL syringe
  • Precise reproducible flow rates
  • Selectable infusion rates units: mL/hr, µL/hr, mL/min, µL/min
  • Click the picture left to see detailed specs.

Micrometer Head
  • One micrometer head is a built-in travel rod of the coater to adjust the gap between slot die and substrate
  • A digital micrometer head is available as an option at an extra cost        
         

             Digital Micrometer Head 1" Travel 0.003 mm Accuracy
Travel Speed & Length
  • Travel Speed: 0 - 80mm/sec variable
  • Travel distance: 0 - 400 mm adjustable
Heated Vacuum Bed
\
  • Vacuum chuck made of aluminum alloy with the small hole
  • Vacuum chuck Area: 200 mm(W) x 365 mm(L) (8"W x 14"L)
  • Heating elements are installed inside the chuck which can reach 100ºC Max. 
  • Precision digital temperature controller with +/- 1ºC accuracy
  • One high temperature temped glass plate is put on the vacuum chuck, and substrate will be put on the top
Options
  • Pic.1 and 2 show coated cathode and anode for Li-Ion batteries. Please click here to see how to 
  • It is recommended to operate the coater under a fume hood. (Click Pic.3 for detail.)
  • May need a vacuum mixer to remove air bubbles inside slurry to make uniform coatings (Click Pic.4 )
  • You may need a Slurry Viscosity Tester to make coatings consistent (Click Pic.5 for detail.)
Pic.1    Pic.2    Pic.3

 

Pic. 4    Pic.5
Compliance CE certified
NRTL or CSA certification is available upon request at the extra cost


Application Note
  • Coating thickness is not dependent on or equal to the gap between the slot die head and substrate. 
  • Usually, the gap shall be larger than the coating thickness. Coated thickness is strongly dependent on slurry viscosity, coating speed, and flow speed. ( Lower viscosity, low flow rate, and low speed will result in a thinner film Please practice finding the best parameters which suitable for you
  • Example 5% carbon+ polymer, viscosity: 500mPa·s, substrate: Al foil of 16 um,
    • Gap: 200 um, Slurry feeding rate:: 0.1 ml/minute , Coating speed: 12mm/s
    • Coated film thickness: 10 um +/- 2 um
References

 

×

Dimension:

  • 550mm(L) x 330mm(W) x 420 mm(H)

Net Weight:

  • 40kg

Shipping:

  • Shipping Dimension: 48"(L) x 40"(W) x 37"(H)
  • Shipping Weight: 200 lbs


MTI offers a One-Year limited warranty with lifetime support(may cause a fee) for this product.

The MTI One Year Limited Warranty does NOT cover

  • Consumable parts such as O-rings, crucibles, screws, washers, etc.
  • Any damage and rust resulting from improper storage or maintenance.
  • Any damages caused by the use of corrosive and acidic gases.
  • Any damage resulting from failing to adhere to the individual product's specific operation requirements, such as water cooling, venting, etc.
Manufacturer Part Number: